Westell/Versalink Gateway W Manual. products/pdf/ The Westell® VersaLink™ Gateway provides reliable. w) u • Read online or download PDF • Westell Technologies Versalink W User Manual. Westell W came out in and is still in use today as a simple and powerful DSL modem. Not only is the Westell W a wireless modem, it is also a wired.
|Published (Last):||19 June 2014|
|PDF File Size:||13.28 Mb|
|ePub File Size:||5.68 Mb|
|Price:||Free* [*Free Regsitration Required]|
How to Configure a Westell 327W Modem
After you disable Single Static IP, you must reboot your computer. You may now begin your Account Setup. Click on the clear mankal to clear all counts and statistics not just latency counts. Beginning of Diagnostics Help screens VersaLink status checks the connection. Next, enter a name for your log file in the field labeled File name and click on Save.
The Route table maintains the routes or paths of where specific types of data shall be routed across a network. This does not affect the configuration values. Click on OK in the pop-up screen.
Indicates whether manuak static route should be advertised via RIP. Macintosh computers must install via Ethernet connection. Figure 12 may pop up, depending on how Windows 98 SE was installed on the computer. If you click on reset, this screen will refresh and display your last saved RIP configuration.
Don’t show me this message again.
westell versalink w manual Questions & Answers (with Pictures) – Fixya
The following screen will be displayed If you click edit, the following screen will be displayed. After a brief delay, the home page will be displayed.
A Wireless device must be connected to the Gateway for the fields in this screen to be populated. The host name is entered in the input box. Select Search for the best driver for your device. This feature first assigns a high priority to TCP signaling packets in the upstream direction, then places the packet in one of several transmit queues based on this priority. VersaLink has failed to obtain the resolved address.
If you clicked on save, in the preceding DHCP Configuration screen, the following pop-up screen will appear. Windows will display the location of the driver Figure After the computer has restarted, VersaLink is ready for use.
The type of message displayed depends on the menu that you are viewing. The Gateway will not reboot. Video of the Day. A check mark will appear in the box. The WAN Configuration screen will be displayed. Westell has developed an extensive list of NAT services and you may select any service from this list.
Westell Technologies 327W User Manual
Windows 98 SE 2. Westell advises setting this to enabled for the private LAN. At the Save Web Page dialog box, select a destination for your log file from the Save in drop-down arrow. Windows 98 SE Note: Consult your ISP for installation instructions. The connection rate values represent the transmission speed of your DSL line. The NAT profile may then be associated with a manuql profile, allowing you to customize profiles for specific users.
Page of Go. Windows 98 SE Rev. Hollan Johnson is a freelance writer and contributing editor for many online publications.
The following is a list of the possible responses: Click on clear diagnostic log to clear the diagnostic log maual. The following chart provides protocol information for the services maanual by VersaLink.
Now click on add.
Westell Technologies Versalink W User Manual | pages
If you click enable, the following pop-up screen will be displayed. Security Level High High security level only allows basic Internet functionality. This is the station firmware that the card would use to operate 37w a wireless station.
She has been writing professionally since and her interests are travel, gardening, sewing and Mac computers. Refer to section 20 in this User Guide for further details.
Simply connect the hardware, apply power, and perform the simple software configuration for VersaLink and you are on the Internet. The Locate Driver Files window appears.
This screen will allow you to set up your account profile. OUT-Fragments The number of successful transmissions made. The following instructions explain how to install VersaLink for simultaneous use of Ethernet and Wireless ports. Static NAT is now enabled for the device you selected. Enter text from picture: If you are viewing a pop-up screen, click the help link in the pop-up screen to obtain help messages.
If you want to set up advanced features for VersaLink, follow the instructions provided in sections 11 through