No Comments on 61F-GP-N2 OMRON PDF

61F-GPN2 AC from OMRON >> Specification: Liquid Level Controller, 61F- GP-N2 Series, Conductive, Vac, W, 80 ms. Find great deals for Omron 61F-GP-N2 Processor/Controller. Shop with confidence on eBay!. The 61F-GP-N2-AC is a Conductive Level Controller for automatic water supply and drainage control. Compact plug-in controller for single or two-point.

Author: Yozshushicage Kalmaran
Country: Comoros
Language: English (Spanish)
Genre: Life
Published (Last): 3 September 2007
Pages: 425
PDF File Size: 18.61 Mb
ePub File Size: 3.82 Mb
ISBN: 997-9-13825-368-5
Downloads: 9072
Price: Free* [*Free Regsitration Required]
Uploader: Gucage

Product specifications and accessories may be changed at any time based on improvements and other reasons. Limitation 61f-gpn2 Liability; Etc. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty.

Usually, electrodes are used in a set of three: Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. The earth terminal must be grounded.

Connect the short electrode to E1, the medium electrode to E2, and the long electrode to E3. Similarly, avoid using next to a high-capacity contactor which may impacts at operation. Used for sewage, sea water, etc.

61F-GP-N2 – OMRON Industrial Automation

When in 16f-gp-n2, special part numbers may be assigned to fix or establish key specifications for your application. Iron is more reactive than copper. Fully fit the electrode into the connecting nut attached to the electrode holder.


Ideal for soft drink vendors, etc. In this case the relay does not de-energize until the water level falls below the low-level probe. Indication of liquid buildup due to filter blockages.

Doing so causes malfunctions by getting vulnerable to induction noise. Special 3-pole holder of small size and light weight. Return of any Products by Buyer must be approved 61f–gp-n2 writing by Omron before shipment. Between electrode E2 and E3 Response time Operate: For low specific liquids. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.

Ideal for use in tanks where temperature or pressure inside the tank is high, e. When using a noise filter, check the voltage and current and install it as close to the product as possible. Secure the connecting nut by tightening the lock nut and spring washer. For acids, alkalis and sea water, electrode holders may be as much as 1 meter apart to operate properly. It is our practice to change part numbers when published ratings or features are changed, or when significant construction omeon are made.

After fixation, osmium staining, and dissection the Between electrode E1 and E3 Release resistance Approx.

Omron 61F-GP-N2 Processor/Controller

The diagram shows the connections for water supply. Standard electrodes are made of stainless steel and usable in purified water, sea water, sewage, acid except acetic acid, sulfuric acid, etc. However, a type having 1, mm length electrodes is available on request. Precautions for Safe Use 1. If the sufficient interval cannot be provided, employ a low-sensitivity type Floatless Level Controller. A low voltage is applied between these probes and the earth probe or tank, if it is electrically conductive.


These are cut to length and 61f-g-n2 vertically into the liquid. Mounting style Flange Insulator material Phenol resin Max. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. However, some specifications of the Product may be changed without any notice.

o,ron Tighten the electrode with the two clamp screws. When the required length of the electrode is more than 1 m, use a separator at each joint of two electrodes 61f-gp-nn2 as to prevent the electrodes from contacting one another.

In sewage use, electrode holders must be installed 10 to 20 cm apart from one another. This is a temporal bone which had an implant electrode Alarm control warning of abnormal or dangerously high or low levels.

Omron 61F-GP-N2 Processor/Controller | eBay

To convert grams into ounces, multiply by 0. Using the low-level probe allows a wide differential between switching a pump on and off, and can avoid excessive pump operation during tank emptying or filling. Electrochem review part 1 Consider the following two reactions: