AMERICAN AUDIO V1000 PDF

      No Comments on AMERICAN AUDIO V1000 PDF

Results 1 – 34 Valuation Report for Used V Power Amplifier by American Audio (Specs: 2 ( Stereo), x 2 @ 8, Bridgeable). Output Power: W RMS Per Channel @ 4 Ohms, 1kHz, % THD W RMS Per Channel @ 8 Ohms, 1kHz, % THD – Bridge Mode, Mono W RMS. Download AMERICAN AUDIO V V SCH service manual & repair info for electronics experts.

Author: Faurisar Faezragore
Country: Kuwait
Language: English (Spanish)
Genre: Sex
Published (Last): 13 March 2008
Pages: 43
PDF File Size: 15.57 Mb
ePub File Size: 2.73 Mb
ISBN: 719-1-98329-202-5
Downloads: 33826
Price: Free* [*Free Regsitration Required]
Uploader: Maudal

Connect a XLR cable to the input of channel one. During low level output the fans run at normal speeds. These amplifiers are designed to provide a big impact in sound reproduction. Power Switch – This switch controls the units main power.

Be sure not to raise the volume to the clip level, however an intermittent clip signal is acceptable. The limiter has a fixed threshold and can not be adjusted.

Short Circuit Protection can audip be traced back to the signal output line i. Dieses Symobl soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen, die Handhabung und Wartung des Produkts betreffen. This amplifier is designed to mount into a standard 19″ rack. Cooling Fan – Dual speed cooling fans. No user serviceable parts inside.

If the carton appears to be damaged, carefully inspect your unit for any damage and be sure all accessories necessary to operate the system have arrived intact. However, if it is pushed hard enough to continually light the “CLIP ” indicator, the amplifier’s average audko power can reach watts. Cooling Fan – This breaker is designed to protect the amplifier and your speakers in the event of an AC overload.

  KANT PARALOGISM PDF

When the input signal overloads, the “CLIP LED’s” indicate a signal overload, at this time, the master volume should be lowered to reduce distortion. After inserting the wire into the binding post hole, screw the binding post cap down on the wire.

Service Hours are Monday through Friday 9: The exclamation point triangular symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the user manual accompanying the amplifier. Insert the spade connector in to the binding post and tighten the caps down on the spade connector.

At this point channel one will begin to distort. This booklet contains important information americann the proper and safe operation of your new amplifier.

VLP1000 power amplifier

During normal operation below clipping, and momentary clips on peaks, the limiter does not affect the audio signal and is inaudible. Turn your equipment on your amplifier audo always be the last item you turn on. If it is lit about half the time, the amplifier channel will probably go into thermal protection within a few minutes.

When connecting your speakers to the amplifier using banana jacks; Amefican sure that the red and black caps on the binding post are tighten down completely. You’re reading an excerpt. Please read and understand this manual completely before attempting to operate your new amplifier. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen. Always use the 50 Hz filter setting if you are using the amplifier to drive a distributed line system also known as a constant-voltage line, 70 volt line, etc.

  ICBC PROSPECTUS PDF

Ground Lift Switch This switch is used to disconnect the internal ground signal from the amplifier chassis ground. Ensuring americzn polarity will avoid speakers being out of phase, that can cause a loss of bass response. Please do not return the amplifier to amedican dealer without contacting customer support.

See page 9 for more details on input configuration. Amplifiers arrive to you preset in the stereo operation mode.

AMERICAN AUDIO V POWER AMP AMPLIFIER WATTS NR! | #

Mono bridge operation connections will follow the above descriptions however, when operating in mono bridge operation the speaker connections will run between the two positive red leads. The appliance has been exposed to rain or water. Refer all servicing to qualified service personnel. Use channel two positive output terminal americaan the negative connection and the channel one positive output terminal for the amrrican connection. The diagram below detail the functions of each dip switch, the functions are also printed on the rear panel of the amplifier.

Connect an input signal to channel one. The power-supply cord or the plug has been damaged. The speaker wire may be connect by bare wire directly connected, usually for permanent connectionsbanana plug, or spade connector.