Results 1 – 34 Valuation Report for Used V Power Amplifier by American Audio (Specs: 2 ( Stereo), x 2 @ 8, Bridgeable). Output Power: W RMS Per Channel @ 4 Ohms, 1kHz, % THD W RMS Per Channel @ 8 Ohms, 1kHz, % THD – Bridge Mode, Mono W RMS. Download AMERICAN AUDIO V V SCH service manual & repair info for electronics experts.
|Published (Last):||25 December 2008|
|PDF File Size:||19.72 Mb|
|ePub File Size:||19.92 Mb|
|Price:||Free* [*Free Regsitration Required]|
Each channel operates independently of each other allowing each channel to have different filter settings. Um ddas Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. When connecting your speakers to the amplifier using banana jacks; Be wmerican that the red and black caps on the binding post are tighten down completely.
To reset the breaker, push it in. If the carton appears to be damaged, carefully inspect your unit for any damage and be sure all accessories necessary to operate the system have arrived intact. If this line good, check the internal speaker connections and components. These amplifiers are designed to provide a big impact in sound reproduction. Detailed instructions for use are in the User’s Guide.
You’re reading an excerpt. However, if it is pushed hard enough to continually light the “CLIP ” indicator, the amplifier’s average output power can reach watts. Clipping should be kept americn a reasonable minimum. During low level output the fans run at normal speeds.
Turn your equipment on your amplifier should always be the last item you turn on. Insert the banana jacks into the caps of the binding post, be sure that the banana jack is inserted securely to avoid the risk of it popping out. Be sure your amplifier and all other audio anerican is powered down.
You may also visit us on the web at www. Turn your amp on.
Connect an americab signal to channel one. The unit also provides a way to rear mount the unit into a rack for added security.
Below rated output, 8 ohms americah, unweighted dB, unweighted dB, unweighted dB, unweighted dB, unweighted Power Consumption: Insert the bare wire into the hole that was reveled by unscrewing the binding post cap. Mono bridge operation connections will follow the above descriptions however, when operating in mono bridge operation the speaker connections will run between the two positive red leads.
Under heavy clipping activity lower the channel one gain control to reduce there details on input configuration. Never block the fan in any way or mount in an enclose rack, doing so may cause the amplifier to overheat and fail. A short circuit will usually be traced to a bad cable or a bad speaker component and is rarely traced to the amplifier itself. When the input signal decreases enough that clipping ends, the limiter will deactivate and cease its gain reduction.
Ensuring proper polarity will avoid speakers being out of phase, that can cause a loss of bass response. If it is lit about half the time, the amplifier channel will probably go into thermal protection within a few minutes.
Service Hours are Monday through Friday 9: The limiter has a fixed threshold and can not be adjusted. Use the channel one gain to regulate your amplifier output. If the breaker continues to pop, stop using the amplifier and contact customer service. Check the line from the output terminal of the amplifier to the speaker.
V Power Amplifier by American Audio Valuation Report by
If the input gain level is not reduced the built-in limiter will activate. This fan is used to cool the internal parts of the amplifier when in use. Please do not return the amplifier to your dealer without contacting customer support. Except for an occasional flash, keep the “CLIP ameridan indicator dark to avoid overheating the amplifier channel.
The Output Short Circuit V Protection protects the output devices of the amplifier from short circuits and stressful loads. Low Cut Filter V and V Only – The low-cut filter removes extremely low frequencies from the audio signal that could cause speaker distortion or damage.
AMERICAN AUDIO V1000 POWER AMP AMPLIFIER 1000 WATTS NR!
Ameerican excessive clipping the limiter will reduce the audio signal enough to minimize the amount of clipping. The exclamation point triangular symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the user manual accompanying the amplifier.
See page 9 for more details on input configuration. Never plug your amplifier in to a wall outlet that does not match the required voltage of your amplifier, serious damage may occur to your unit. The lightning flash with an arrow triangular symbol is intended to alert the user to the presence of non insulated “dangerous voltage” within the products enclosure, and may be of sufficient magnitude to constitute a risk of electric shock.
This amplifier is designed to mount into a standard 19″ rack.