APL 5912 PDF

      No Comments on APL 5912 PDF

APL datasheet, APL circuit, APL data sheet: ANPEC – V Reference Ultra Low Dropout ([email protected]) Linear Regulator,alldatasheet, datasheet. APL datasheet, APL circuit, APL data sheet: ANPEC – V Reference Ultra Low Dropout (V5A) Linear Regulator,alldatasheet, datasheet . APL中文资料_电子/电路_工程科技_专业资料。2b. com APL V Reference Ultra Low Dropout ([email protected]) Linear Regulator.

Author: Mikashakar Kigakinos
Country: Liechtenstein
Language: English (Spanish)
Genre: Education
Published (Last): 3 February 2013
Pages: 235
PDF File Size: 18.19 Mb
ePub File Size: 17.57 Mb
ISBN: 872-1-86929-627-3
Downloads: 15250
Price: Free* [*Free Regsitration Required]
Uploader: Grocage

When the voltage on FB pin falls below the under-voltage threshold, the UVP circuit shuts off the output immediately. Add to watch list.

If you’d like to get the additional items you’ve selected to qualify for this offer, close this window and add these items to your cart. APL datasheet and specification datasheet.

Interest will be charged to your account from the purchase date if the balance is not paid in full within 6 months. Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab. Select a valid country.

1 PCS New APLKAC-TRL APL SOP-8 IC chip | eBay

Ultra-low-ESR capacitors, such as ceramic chip capacitors, are very good for the input capacitors. Refer Figure 3 to make a proximate topology. The output voltage set by the resistor divider is determined The Exposed Pad provide a very low impedance input zpl for the main supply voltage.

  CASIO AQ-164W MANUAL PDF

See other items More All other trademarks are the property of their respective ap. Please connect PIN 3 and 4 together by a wide track or plane on the Top layer.

APL Anpec Electronics, APL Datasheet

Please enter a number less than or equal to Ceramic decoupling capacitors for load must be placed near the spl as close as possible. Seller information domoki The regulator regulates the output again through initiation of a new softstart cycle after the junction temperature cools by 50oC, resulting in a pulsed output during continuous thermal overload conditions.

All item you’ve selected was not added to your cart. The output capacitor selection is to select proper ESR equivalent series resistance and capacitance of the output capacitor for good stability and load transient response. All voltage levels are measured with respect to this pin.

All temperatures refer to topside of the package. When re-enabled, the IC undergoes a new soft-start cycle.

10pcs APL5912KAC APL5912 SOP-8

592 making your offerif the page does not update immediately. Select a proper R1 selected to be a little larger than the calculated R1.

Please enlarge the area to reduce the case-to-ambient resistance? The POR function initiates a soft-start process after the two supply voltages exceed their rising POR threshold voltages during powering on.

Large current paths must have wide tracks. When the voltage on FB pin falls below the under-voltage threshold, the UVP circuit shuts off the output immediately Learn more – opens in a new window or tab. Sign in to check out Check out as guest. Input Capacitor The APL requires proper input capacitors to supply current surge during stepping load transients to prevent the input rail from dropping. Please connect Pin 3 and 4 together using wide tracks. Shipping cost cannot be calculated.

  DYNAUDIO MW160 PDF

SOP-8 APL5912 APL591

Internal Soft-Start An internal soft-start function controls rise rate of the output voltage to limit the current surge at start-up. The SOP-8 cost-effective package featuring a small size like a standard SOP-8 and a bottom exposed pad to minimize the thermal resistance of the package, being applicable to high current www.

Pulling and holding the EN pin below 0. Get the item you ordered or get your money back.

Lead Free Device Blank: Read more about aapl condition. Description Description 1 inkFrog Analytics. During load transients, the output capacitors, depending on the stepping amplitude and slew rate of load current, are used to reduce the slew rate of the current seen by the APL and help the device to minimize the variations of output voltage for good transient response. Contact the seller – opens in a new window or tab and request a shipping method to your location.