ARMY TM &P* AIR FORCE TO 11W .. PURPOSE OF EQUIPMENT The M68 Reflex Sight w/Quick Release Mount is used on the. M68 Reflex Sight Manual. This is an illustrated operator and maintenance manual TM &P for the U.S. Army M68 reflex sight. Soft cover, B/W, . The TA31RCO is an Advanced Combat Optical Gunsight (ACOG) designed for the US Army’s M4 weapon system (” barrel). It incorporates dual illumination .
|Published (Last):||7 July 2008|
|PDF File Size:||6.28 Mb|
|ePub File Size:||8.1 Mb|
|Price:||Free* [*Free Regsitration Required]|
Then, using a meter boresight target, the weapon can be boresighted with any optic, laser, or iron sight that the soldier is assigned to fire. This fundamental is not affected by night firing conditions using the Armu.
To retain zero, remove the TPIAL and rail grabber as a whole assembly and place back onto the same notch as removed.
Extensive testing has proven that the average soldier does not properly use the night vision devices. In most cases, the amry weld no longer exists. Dry fire is done to allow the soldiers to make adjustments to the TWS. During practice qualification and qualification, it is the soldiers preference on polarity and field of view. Have the firer get behind the weapon in a stable supported firing position and look through the TWS.
The art of target detection at night is only as good as the soldier practices. The procedures for record qualification are:.
The fundamentals are changed as follows:. The aiming method used to zero must also be used to engage targets. The M68, CCO is a reflex nontelescopic sight. If the firer does not get the same sight picture after the second realignment, he more than likely has a fundamentals problem scog his firing position and sight picture.
The same is true with the human body-a person moving generates more heat than someone standing still. Rotate the borelight back to the start point; move the zeroing mark to the visible laser.
Anyone know the TM (Army) number for an ACOG?
Record qualification with the TWS is the same as day record qualification with iron sights. Regular blinking during scanning relieves some of the eyestrain that the soldier tends to have trying to spot distant targets.
The objective is to not disrupt alignment of the laser with the target by jerking the trigger. Regardless of the mounting location, the adjuster that is on top or bottom will always be the adjuster for elevation and the one on the side will be the windage adjuster. Place the zeroing gm approximately 10 meters from the end of the barrel so that the visible laser strikes the zeroing mark. Before boresighting ensure that the borelight has been zeroed to the weapon.
The night initial training strategy is used for soldiers who have little or no previous experience with night vision goggles, or for units beginning a night-training program. Aim the red dot of the M68 on the crosshair located on the meter boresight target.
Weapon stability is crucial in boresighting. Other procedures are the same as standard iron sight procedures. Two soldiers a firer and a target holder are required to properly boresight a weapon.
When the visible laser is adjusted to the reference arrmy at 2 meters, then start the procedure again at 10 meters. The integrated act of firing with the M68 is identical to the iron srmy except for the change in sight picture. The backup iron sight BIS is a semi-permanent flip up sight equipped with a rail-grabbing base. Starting with a securely installed and live-fire zeroed BIS, mount the reflex sight to the front of the receiver rail or to the top RAS as preferred.
From this point, make 4×4 squared box around the point of impact. If the gunner still has the proper boresight alignment the gunner is boresighted; otherwise he will need remedial training on his sight picture. Enter Your Email Address.
Anyone know the TM (Army) number for an ACOG? | Yahoo Answers
Pokemon pearl iron tail tm number? Each field of view has its own advantages and disadvantages. Qualification standards are the same for day and night.
Regular blinking during scanning relieves some of the eyestrain that the soldier tends to have trying to spot far targets. Practice qualification with the TWS is the same as day practice qualification with iron sights. This requires the firer to ensure that he acquires the same sight picture and cheek-to-stock weld position each time in order to get a solid boresight. Make adjustments ary the windage and elevation of the iron sights until the borelight is centered with the circle on the boresight target.