1 This practice is under the jurisdiction of ASTM Committee A01 on Steel, Last previous edition approved in as A – 99 (). May 2nd, – Below is a technical summary of specification ASTM A 99 Advanced Plating Technologies is not. Gold plating is an exceptional finish for. BOOK ID: ECUadPJ && Download Book Pdf Astm A Finish Free. Passivation Services â€“ Welcome to Scott Metal Finishing. ASTM A 99 Advanced.
|Country:||Moldova, Republic of|
|Published (Last):||9 November 2013|
|PDF File Size:||2.53 Mb|
|ePub File Size:||12.67 Mb|
|Price:||Free* [*Free Regsitration Required]|
In addition, visual inspection of internal surfaces is often impossible because of the configuration of the item.
Article: Passivation of stainless steels
In order to avoid ambiguity in the setting of requirements, it may be necessary for the purchaser to define precisely the intended meaning of passivation. Specific treatments are however astj specified. It therefore in no way precludes the necessity for careful planning and judgment in the selection and implementation of such procedures.
Citric acid passivation as an alternative to nitric acid treatments Citric wstm treatments can also be considered as an alternative to nitric acid as both provide the oxidising conditions necessary for passivation. Visual inspection is suitable for the detection of gross contamination, scale, rust, and particulates, but may not reveal the presence of thin films of oil or residual asstm films.
Citric acid treatments can also be considered as an alternative to nitric acid as both provide the oxidising conditions necessary for passivation. Unlike ASTM A, the standard does not require specific solutions for particular stainless steel grades or types, although 3 specific treatments are identified.
This process is described in a general way in 6. Unless otherwise specified, it is this definition of passivation that is taken as the meaning of a specified requirement for passivation. The treatments are then defined by the process classes. On the other hand, some of the practices adtm be applicable for these purposes.
Link to Active This link will always route to the current Active version of the standard. Office and Postal Address: Stainless steels are designed to naturally self-passivate whenever a clean surface is exposed to an environment that can provide enough oxygen to form the chromium rich oxide surface layer, on which the corrosion resistance of these alloys depends.
Some of the various meanings associated with the term passivation that are in common usage include the following:. Passivation of stainless steels Introduction Stainless steels are designed to naturally self-passivate whenever a clean surface is exposed to an environment that can provide enough oxygen to form the chromium rich oxide surface layer, on which the corrosion resistance of these alloys depends.
The standard also allows any combination of citric acid concentration, temperature and time, provided that the passivation test criteria can be met.
ASTM A Passivation Standard | Able Electropolishing
Others, such as food-handling, pharmaceutical, aerospace, and certain nuclear applications, may require extremely high levels of cleanness, including removal of all detectable residual chemical films and contaminants that are invisible to ordinary inspection methods. In the case of classes C3 and C4, a two step process is defined, with a clean water rinse between the two steps, shown in the table below. For certain exceptional applications, additional requirements which are not covered by this practice may be specified upon agreement between the manufacturer and the purchaser.
For more specific safety precautions see 7. It a830 at one time considered that an oxidizing treatment was necessary to establish this passive film, but it is now accepted that this film will form spontaneously in an oxygen-containing environment providing that the surface has been thoroughly cleaned or descaled. The degree of cleanness required on a surface depends on the application. Referenced Documents purchase separately The documents listed below astj referenced within the subject standard but are not provided as part of the standard.
Naturally occurring conditions such air or aerated water will do this and so under many exposure conditions stainless steels will naturally self-passivate. In some cases, no more than degreasing or removal of gross contamination is necessary.
Citric acid is a less hazardous method and has environmental sstm in terms of ‘NOx’ fume emission and waste acid disposal. Specifications for passivation treatments for stainless steels Traditionally the American standards have been used.
Stainless steels cannot be passivated unless the steel surface is clean and free from contamination and scale from welding operations.
Passivation treatments are sometimes specified, but it is important to consider whether this is strictly necessary or not. This standard covers both nitric and citric acid treatments.
ASTM A380 Passivation Standard
Methods are described for the detection of free iron and transparent chemical and oily deposits. Process Class Stainless Steel Types C1 or C2 Austenitics, austenitic precipitation hardening and duplex C3 High chromium martensitics C4 Ferritics, martensitics and martensitic precipitation hardening. Active view current version of standard.
In addition, this standard also includes citric acid treatments. Parts treated however must pass specific tests to confirm the effectiveness of the passivation, although in practice the tests are for the detection of the effects of residual iron contamination on the surface of the parts. Some of the various meanings associated with the term passivation that are in common usage include the following: It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Featured Articles & Publications
The standard notes that the high carbon martensitic stainless steels, such as C, are not suitable for acid passivation as they can be attacked or be subject to hydrogen embrittlement. Related Links Suppliers of Passivating Products. The term “iron,” when hereinafter referred to as a surface contaminant, shall denote free iron. These astj are presented as procedures for guidance when it is recognized that satm a particular service it is desired to remove surface contaminants that may impair the normal corrosion resistance, or result in the later contamination of the particular stainless steel grade, or cause product contamination.
Such chemical treatment is generally not necessary for the formation of the passive film. Although they apply primarily to materials in the composition ranges of the austenitic, ferritic, and martensitic stainless steels, the practices described may also be useful for cleaning x380 metals if due consideration is given to corrosion and possible metallurgical effects.
Range C Time mins. Meaningful tests to z380 the degree of cleanness of a surface are few, and those are often difficult to administer and to evaluate objectively.
While the practice provides recommendations and information concerning the use of acids and other cleaning and descaling agents, it cannot encompass detailed cleaning procedures for specific types of equipment or installations.