Designation: B /B M – Standard Specification for. Aluminum Bronze Rod, Bar, and Shapes1 This standard is issued under the fixed designation B. Chemical Composition according to ASTM B/BM(). 1Cu value includes Ag. %emsp;2Ni value includes Co. Note: Cu + Sum of Named Elements, . ASTM B/BM(). Standard Specification for Aluminum Bronze Rod, Bar, and Shapes. standard by ASTM International, 04/01/ View all product.
|Published (Last):||19 April 2008|
|PDF File Size:||16.39 Mb|
|ePub File Size:||11.8 Mb|
|Price:||Free* [*Free Regsitration Required]|
A superscript epsilon e indicates an editorial change since the last revision or reapproval. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.
ASTM B / BM – 12() Standard Specification for Aluminum Bronze Rod, Bar, and Shapes
With the Mercurous Nitrate Test, equipment for the detection and removal of mercury vapor produced in volatilization, and the use of protective gloves is recommended. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Xstm on Standards, at the address shown below. Stainless Steel H Combining values from the two systems may result in non-conformance with the standard. B and B M were combined.
When the alloy was first produced as a casting, it was found that occasionally the alloy suffered selective corrosion of the kappa phase. B Elongation values are based on 5. The new wrought alloy has a quench and temper heat treatment which eliminated this problem introducing a structure that changed the morphology of the kappa b105.
Historical Version s – view previous versions of standard. C Yield strength at 0. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.
ASTM B150 & B150M -03
By agreement between the manufacturer and the purchaser, limits may be established and analysis required for unnamed 1b50. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
Originally approved in Approved May 10, C is specified, the tolerances for diameter, thickness, width, and length shall be part of the contract or purchase order and shall be agreed upon between the supplier and the purchaser.
Stress relief annealing is a method of thermal stress axtm. C and C HR50 drawn and stress relieved rod and bar: Please help us to share our service with your friends. In any case, a minimum gage length of 1 in.
We are a non-profit group that run this website to share documents. C and Astk in tempers listed in Table 3, Rockwell hardness shall be the basis of acceptance or rejection for mechanical properties except when the tensile test is speci?
ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. In addition, the alloy has excellent wear resistance and b1150 corrosion resistance in fresh and sea water.
ASTM B & BM – Free Download PDF
C Yield strength at 0. Bar straightening is a method of mechanical stress relief.
Link to Active This link will always route to the current Active version of the standard. B10 Silicon Bronze C It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
See Ordering Information and Other Requirements sections. We need your help! Approved April 15, Products shall be tested and shall conform to dimensional mass, diameter, length, thickness, straightness, and edge contourmechanical tensile and yield strength, Rockwell hardness, and elongationand chemical composition requirements.
When the product is for subsequent welding aastm and is so astmm Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
Stainless Steel Condition B. Beryllium Copper Alloy C Dimensions, Mass and Permissible Variations C and C HR50 drawn and stress relieved rod and bar: Current edition approved April 15, This specification establishes the requirements for rods, bars, and shapes of aluminum bronze with Copper Alloy UNS Nos. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
Materials and Manufacture 5. Users of this standard are expressly advised that determination of the v150 of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.