ASTM B26 PDF

      No Comments on ASTM B26 PDF

Aluminum Alloys. Refer to ASTM Specification B26/B26M Chemical Compostion (%Max, unless range is stated). Others. ANSI Alloy #. UNS. Si. Fe. Cu. Mn. ASTM B26/B26M: Standard Specification for Aluminum-Alloy Sand Castings. ASTM B26/B26M Standard Specification for Aluminum-Alloy Sand Castings. standard by ASTM International, 05/15/ This document has been replaced.

Author: Nizilkree Gozil
Country: Paraguay
Language: English (Spanish)
Genre: Education
Published (Last): 28 November 2018
Pages: 117
PDF File Size: 2.84 Mb
ePub File Size: 10.79 Mb
ISBN: 279-6-73456-559-8
Downloads: 19105
Price: Free* [*Free Regsitration Required]
Uploader: Vudora

Link to Active This link will always route to the current Active version of the standard. Historical Version s – view previous versions of standard.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Note 3—The following applies to all specified limits in this table: It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.

Pure metals, recycled materials, and master alloys can also be used to make the alloys as long as the chemical composition can be analyzed and b266 to conform to the requirements prior to pouring any casting. Unified Numbering System wstm designations are in accordance with Practice E A Contains silver 0.

  M.L.ANDREASEN BOOKS PDF

It may not address the mechanical properties, integrity testing, and verification required for highly loaded or safety critical applications. Note 2—Analysis shall be awtm for the elements for which limits are shown in this table.

ASTM-BB26M ADOPTION NOTICE ALUMINUM ALLOY SAND CASTINGS

C Contains beryllium 0. B If iron exceeds 0.

Addition of small amounts of modifiers and grain refining elements to the molten alloys from the remelting furnace is permitted before casting. It may not address the mechanical properties, integrity testing, and verification required for highly loaded or safety critical applications. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. This specification covers aluminum alloy sand castings except those that are for aerospace applications.

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are aztm, complete or up to date. Note 1—When single units are shown, these indicate the maximum amounts permitted. Referenced Documents purchase separately The documents listed below are referenced satm the subject standard but are not provided as part of the standard.

Castings should only be repaired using approved processes such as welding, impregnation, peening, blending, soldering, and so forth. The chemical compositions are determined in accordance with the specified suitable chemical and spectrochemical test methods.

  DEADLAND RULEBOOK PDF

This abstract is a brief summary of the referenced standard.

Active view current version of standard. Link to Active This link will always route to the current Active version of the standard.

ASTM-B26/B26M, ADOPTION NOTICE: ALUMINUM ALLOY SAND CASTINGS (15-MAY-1992) [SUPERSEDING QQ-A-601F]

Combining values from the two systems may result in nonconformance with the standard. The values stated in asm system may not be exact equivalents; therefore, each system shall be used independently of the other. For purposes of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit in accordance with the rounding method of Practice E Combining values from the two systems may result in nonconformance with the standard.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.