ASTM D6693 PDF

      No Comments on ASTM D6693 PDF

GeoTesting Express is a provider of Geosynthetic Testing Services – ASTM D,Standard Test Method for Determining Tensile Properties of Nonreinforced. ASTM D (D) determines the tensile properties of nonreinforced geomembranes in the form of standard dumbbell-shaped test specimens when tested. Buy ASTM D R TEST METHOD FOR DETERMINING TENSILE PROPERTIES OF NONREINFORCED POLYETHYLENE AND.

Author: Bataur Grojora
Country: Grenada
Language: English (Spanish)
Genre: Travel
Published (Last): 16 June 2013
Pages: 318
PDF File Size: 1.43 Mb
ePub File Size: 10.70 Mb
ISBN: 191-7-19649-717-6
Downloads: 41913
Price: Free* [*Free Regsitration Required]
Uploader: Dat

The constant rate of crosshead movement of this test lacks accuracy from a theoretical standpoint. A wide difference may exist between the rate of crosshead movement and the rate of strain of the specimen indicating that the testing speeds specified may disguise important effects or characteristics of these materials in the plastic state.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. It may be necessary to modify this procedure for use in testing certain materials as recommended by the material specifications.

In cases of such dissimilarity, no reliable estimation of the limit of usefulness can be made for most plastics. However, because of the high degree of sensitivity exhibited by many plastics to rate of straining and environmental conditions, data obtained by d66993 test method cannot be considered valid for applications involving load-time scales or environments widely different from those of this test method.

ASTM D6693 Tensile Test of Geomembranes

Hence, where directly comparable results are desired, all samples should be of equal thickness. Hence, where directly comparable results are desired, all samples should be of equal thickness.

  BELEZNICA KNJIGA PDF

Consequently, where precise comparative results are desired, these factors must be carefully monitored and controlled. Historical Version s – view previous versions of standard. The constant rate of crosshead movement of this test lacks accuracy from a theoretical standpoint.

Further, it is realized that variations in the thicknesses of test specimens, as permitted by this test method, produce variations in the surface-volume ratios of such specimens, asm that these variations may influence the test results.

Similarly, for referee purposes or comparisons within any given series of specimens, care must be taken to secure the maximum degree of uniformity in details of preparation, treatment, and handling.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. This test method is not intended to cover precise physical procedures. Link to Active This link will always route to the current Active version of the standard.

Note—This test method is not intended to cover precise physical procedures. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.

Link to Active This link will always route to the current Active version of the standard. Special additional tests should be used where more precise physical data are needed. The values given in parentheses are for information only.

Active Risk Management

aastm Therefore, it is advisable to refer to that material’s specification before using this test method. Tensile properties may provide useful data for plastics engineering design purposes. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

  ECONOMIA FISCHER DORNBUSCH SCHMALENSEE PDF

Combining values from the two systems may result in non-conformance with the standard. This sensitivity to rate of straining and environment necessitates testing over a broad load-time scale and range of environmental conditions if tensile properties are to suffice for engineering design purposes.

These data are also useful for qualitative characterization and for research and development. Special additional tests should be used where more precise physical data are needed. Active view current version of standard. Further, it is realized that variations in the astk of test specimen, as permitted by this test standard, produce variations in the surface-volume ratios of such specimens, and that these variations may influence the test results.

ASTM D Tensile Test of Geomembranes

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. A wide difference may exist between the rate of crosshead movement and the rate of strain of the specimen indicating that the testing speeds specified may disguise important effects or characteristics of these materials in the plastic state.

Hence, when comparative tests of materials are desired, the care must be exercised to ensure that all samples are prepared in exactly the same way, unless the test is to r6693 the effects of sample preparation.