Designed for the contractor, the CPS MK II feature 2-RU chassis, Phoenix-type connectors for inputs and outputs, pre-programmable power-on delay, easy power-on via remote contact closures, rear panel attenuators, and a switchable 50 Hz high-pass filter. Like the CPS multi. Two-Channel Models CPS, CPS, CPS, and CPS CPS2.x rear view. Remote power-on contact. 1. Programmable power-on timer. 2. Module slot for. Buy Electro-Voice CPS 2-Channel Power Amplifier for RCM IRIS-Net Remote Control Module (W, 4 Ohms) Review Electro-Voice CPS
|Published (Last):||16 January 2012|
|PDF File Size:||5.88 Mb|
|ePub File Size:||5.78 Mb|
|Price:||Free* [*Free Regsitration Required]|
CPS MKII Power Amplifier by Electro-voice, Inc. (ev) Valuation Report by
Also See for CPS2. For fixed amplifier installations in a device control room that incorporate a central air-cooling system or air conditioners, calculating the maximum heat emission may be necessary. Whenever possible, using balanced audio signal feeds at the input of the power amplifier is always preferred. The audio signal has to be applied to the input connectors of channel 1, amplification is set via input level control of channel 1 only.
Please read and follow the instructions provided in the documentation that you have received together with each extension module. Do not use the power amplifier near heat sources, like heater blowers, stoves or any other heat radiating devices.
Electro-Voice CPS 2-Channel Power Amplifier FU B&H
The terminals marked with are hazardous live and the external wiring connected to these terminals requires installation by an instructed person or the cpps2.9 of ready-made leads of cords. Set the switch to the OFF position if no attenuation of low frequency audio signals is required.
The power amplifier remains cooler and dissipating the developing waste heat in a specific direction gets easier. Electrovoice contractor precision cps2t: Unbalanced connections should only be used if the cables are very short and no interfering signals are to be expected in the vicinity of the power amplifier.
Electro-Voice Cps2.9 MKII Contractor Class-h Power Amp 2×900 Watts
Turning the Mains Switch to ON starts booting up the power amp. Failure to do so may result in damage to the power amplifier as well as to the wv case.
The audio signal has to be applied to the input connectors of channel 1. Comments to cps.29 Manuals Your Name. Turning the control to the right increases and turning it to the left decreases the volume. Attach the power amp with its frontal rack mount ears using 4 screws and washers as shown in following illustration.
The correct connection is also indicated at the amplifiers rear panel.
Additionally securing the amplifier at the rear becomes necessary, if the rack case in which the power amplifier has been installed will be transported. Table of Contents Add to my manuals Add. The connected speaker systems must be able to handle such voltages.
Mains Switch Rear View 1. F reserved Table 4. This manual also for: Enter text from picture: Don’t have an account? Do not use the power amplifier near heat sources, like heater blowers, stoves or any other heat radiating devices.
This mode of operation is being used for all 2-channel applications, like stereo operation. Ventilation As with all Electro-Voice power amps with fan cooling, the airflow direction is front-to-rear, obviously because there is more cold air outside of the rack case than inside.
Electro-Voice CPS2.9 Manuals
Do not modify this unit! The amount of heat resulting from power dissipation might remain inside of a rack-shelf and needs to be diverted using appropriate measures. Only the provided power cord may be used. Electrovoice contractor precision cps1: Mounting CPS amplifiers have been designed for installation in a conventional inch rack case. When installing the power amp in a case or rack system, attention should be paid to these details to provide sufficient ventilation.
CPS amplifiers have been designed for installation in a conventional inch rack case.