No Comments on JSS 55555 SPECIFICATIONS PDF

For more details, refer Procedure 6, Test Condition K, Page no of Defence. Standard JSS Rev Low Temperature Test. 3 days ago , Document No. Nomenclature, Standardisation Sub-Committee. , (Third Revision), COMPOSITION FLARES, BEACON. recommended as per JSS, Military standard, Class L2H category, and functional specifications and no damages should be seen as an outcome of.

Author: Goltigal Shalkis
Country: Oman
Language: English (Spanish)
Genre: Technology
Published (Last): 17 May 2015
Pages: 407
PDF File Size: 6.45 Mb
ePub File Size: 5.52 Mb
ISBN: 425-4-17449-588-3
Downloads: 34859
Price: Free* [*Free Regsitration Required]
Uploader: Maukazahn

JSS 55555 – Antifungal Test – Electronics

Choose the one alternative that best completes the statement or answers the question. Why this requirement is important?

Staff Engineer September 25, Moisture can be a problem. Read this operation manual and understand the description.

Corrosion acid see Note 1, 2 and 3 Corrosion alkaline see Note 1,2 and 8 3 After that caps are applied to the rods and tinned apecifications copper wires are welded to these end caps. Failure to follow the safety rules and other basic safety precautions.

Ground equipment partially protected g L2F: Option Card for Frequency Divider. A check may then be made by measuring some other parameter which is temperature dependent and for which the law of temperature dependence is known Test – A complete series of operations covered under a test heading Test Chamber – An enclosure in which the equipment can be exposed to the specified environmental test conditions Test Procedure – A complete series of operations covered by any one heading and shall normally consist of the following ; a Preconditioning where required.

Classification of groups of environmental Jws information.

Environmental testing

Ground equipment partially protected e L2D: Final measurement made at the end of one test may be taken as the initial measurement for the subsequent tests. Dry heat This English-language version is derived from the original bilingual publication More information.


Ground equipment partially protected d L2C: Ground equipment partially protected c L2B: To make this website work, we log user data and share it with processors. No requirement for relative humidity is given because its correction by calculation is generally not possible.

After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded More information. Keeping in view the stringent quality and operational requirements of the users, the Joint Services Specification No on Environmental Test Methods for Electronic and Electrical Equipment JSS was prepared in which was later revised in Considerable experience has been gained over the years since and this has necessitated revision of the existing JSS This document JSS on Environmental Test Methods for Electronic and Electrical Equipment has been reprinted with the various amendments incorporated.

National Electrical Manufacturers Association More information. June 11 th, Report Prepared By: During the visual examination of the equipment, defects in construction, the presence of foreign bodies, moisture, dust, etc. The role of dehumidification in improving coating performances.

EN V2. To be used in the field or in a vehicle where it is fully psecifications to the weather during storage and use and liable to immersion in water. Temperature Relative humidity Air pressure: Failure to follow the safety rules and other basic safety precautions More information.

Spectross – Digital Systems

Weather is a result of the atmosphere s constant attempt to reach equilibrium. The relevant equipment specification shall define the acceptable performance limits during and after the specified environmental tests. A discussion of condensate removal systems for clarifier and thickener drives for specifivations and wastewater facilities. Temperature Rise Above Spec E Temperature stability has been reached when the ratio between consecutive intervals exceeds 1.


Prime Envirotech : Environment Testing Chamber – Roorkee

After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded. Exposure procedure for artificial weathering. DecemberJuneDecemberMarch Liquid-in-glass thermometers selection, use and calibration Copyright National More information.

Classification of groups of environmental. For the purposes of setting a. Final draft EN V2. In such cases the details shall be as given in the relevant equipment specification. To be used in permanent protected unpacked buildings. Gas detectors Selection, installation, use and maintenance More information.

Part 1 Wire cloth test sieves third revision Reaffirmed BS August Amended and reissued: SI units and recommendations for the use of their multiples and of certain other units. II, shocks as per face 24 Note: Specifications are subject to change without notice according to Carrier Policy of continuous development.

Transmission line insulator condition monitoring is of increasing interest with the ageing of many transmission More information. EN V3. Shipborne equipment exposed unpacked c N3: Date Amendment pertains to: It therefore More information. Liquid-in-glass thermometers selection, use and calibration Technical Note 19 March Issued: Content This specification covers performance, tests and quality requirements for the.

Shipborne equipment submersible unpacked: For the purposes of setting a More information.