KSP 2222A DATASHEET PDF

      No Comments on KSP 2222A DATASHEET PDF

KSP. A. NPN Epitaxial Silicon Transistor. Absolute Maximum Ratings Ta=25 °C unless otherwise . This datasheet contains the design specifications for. KSPA transistor is a general purpose transistor and hence fit into many applications, it is a direct substitute for 2NA transistor as both. KSPA Transistor Datasheet pdf, KSPA Equivalent. Parameters and Characteristics.

Author: Zolorisar Dak
Country: Gambia
Language: English (Spanish)
Genre: Health and Food
Published (Last): 6 September 2008
Pages: 196
PDF File Size: 16.56 Mb
ePub File Size: 1.89 Mb
ISBN: 663-1-93312-271-6
Downloads: 1799
Price: Free* [*Free Regsitration Required]
Uploader: Tam

Another Common application of a Transistor is as amplifiers.

Submitted by admin on 24 June It is very similar to a mechanical switch but here we will control the switch using electric signals. There are many types of amplifier circuits that are possible with transistor but this is the most commonly used one because it is very good in amplifying low frequency voltage signals like audio signals. KSPA can allow collector current upto mA and also has power dissipation of mW which can be used to drive larger loads than compared with BC The resistor R1 is called the Base resistor and is very important to drive a transistor, it limits the base current and failing to use one might damage the transistor permanently.

The capacitors C1 and C2 are simply used for filtering purpose. TL — Programmable Reference Voltage. Again the values of the resistor mentioned datasgeet are only for reference commonly used you have to design your own circuit based on the application and transistor you are using.

  HEALTHCARE UNWIRED PDF

The base pin of the transistor has to be biased with a voltage; this voltage is provided by the potential 22222a network formed by the resistors R4 and R6. Applications General purpose NPN transistor Can be used to switch high current upto mA loads It can also be used in the various switching applications.

When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter.

The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor. Every transistor has a gain h FE associated with it, which can be used to amplify voltage or current.

To bias a transistor we have to supply current to base pin, this current I Datahseet should be limited to 5mA.

However this type of amplifiers have many drawback and if you are looking for some serious amplification applications then ,sp should look into Op-Amps which are nothing but a package of many transistors put to gather with amplification as its sole purpose. The vales of the Resistor in the above image are only for reference and are not accurate.

KSPA Datasheet, Equivalent, Cross Reference Search. Transistor Catalog

Normally this type of transistor will either be used as a switch or as an amplifier, both of which is discussed below. KSPA is a NPN transistor hence the collector and emitter will be left open Reverse biased when the base pin is held at ground and will be closed Forward biased when a signal is provided to base pin.

  ANDRONOVO CULTURE PDF

Transistor as Amplifier Another Common application of a Transistor is as amplifiers. The resistor R2 is used to limit the current though the collector of the transistor and is not mandatory.

KSPA 데이터시트(PDF) – Fairchild Semiconductor

So if you looking for an NPN transistor that could switch loads of higher current then KSPA might the right choice for your project. In this type of circuit, the Emitter and the Base pin of the transistor should be commonly connected to a same voltage, so we have connected it to the Ground potential using two resistors R4 and R3.

The transistor will begin to conduct when the voltage across the Base and Emitter pin exceeds 0. But there are two important features that distinguish both.

KSP2222A Datasheet, Equivalent, Cross Reference Search

KSPA has a gain value of tothis value determines the amplification capacity of the transistor. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region.

One of the most default and primary function of a transistor is to act as a switch.